Teledyne-lecroy QPHY-PCIE3 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Logiciel Teledyne-lecroy QPHY-PCIE3. Teledyne LeCroy QPHY-PCIE3 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 28
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
QPHY-PCIE3
Operators Manual
Revision A March, 2014
Relating to the following release versions:
Software Version Rev. 7.3.0.0
Script
PCI_Express_Test_Spec_Electrical_Layer_3_0_rev_0_9
Style Sheet Rev. 1.2
Vue de la page 0
1 2 3 4 5 6 ... 27 28

Résumé du contenu

Page 1 - Revision A – March, 2014

QPHY-PCIE3 Operator’s Manual Revision A – March, 2014 Relating to the following release versions: Software Version Rev. 7.3.0.0 Script PCI_

Page 2

General Setup The first sub-dialog contains general system settings. These remain in effect for each session, regardless of Standard, until changed

Page 3 - Table of Contents

QPHY-PCIE3 Operator’s Manual QualiPHY Test Process Once general system settings are in place, these are the steps for running test sessions. Set Up T

Page 4 - About This Manual

Run Reports The QualiPHY software automates report generation. On the framework dialog, go to General Setup > Report to pre-configure reporting

Page 5 - Introduction

QPHY-PCIE3 Operator’s Manual Customizing QualiPHY The pre-loaded configurations cannot be modified. However, you can create your own test configurati

Page 6

Edit Variables The Variable Setup tab contains a list of test variables. See QPHY-PCIE3 Variables for a description of each. To modify a variable:

Page 7 - Installation and Setup

QPHY-PCIE3 Operator’s Manual Edit Test Limits The Limits tab shows the Limit Set currently associated with the configuration. Any limit set can be as

Page 8 - Set Up Remote Control

X-Replay Mode The X-Replay mode window is an advanced (“developer”) view of QualiPHY. The tree in the upper-left frame enables you to navigate to p

Page 9 - Using QualiPHY

QPHY-PCIE3 Operator’s Manual QPHY-PCIE3 Testing Test Preparation Before beginning any test or data acquisition, the oscilloscope should be warmed for

Page 10 - General Setup

Demo Transmitter Tests This configuration runs all the Transmitter tests (Tests 1.1 – 1.7 below, plus Test 1.4 the Compliance Eye 8 GT/s test) usi

Page 11 - QualiPHY Test Process

QPHY-PCIE3 Operator’s Manual TEST 1.4 – COMPLIANCE EYE 8 GT/S CEM Compliance Eye 8 GT/s. This test forms an eye diagram using 1,008,000 UI from the

Page 12 - 922544 Rev A

700 Chestnut Ridge Road Chestnut Ridge, NY, 10977-6499 Tel: (845) 425-2000, Fax: (845) 578 5985 teledynelecroy.com © 2014 Teledyne LeCroy, Inc.

Page 13 - Customizing QualiPHY

DISPLAY CONNECTION DIAGRAMS This variable enables/disables the display of DUT connection diagrams during the test process. The default value is Yes

Page 14

QPHY-PCIE3 Operator’s Manual TX POSITIVE SOURCE This variable allows the user to specify the channel being used to measure Lane A Tx+. TX2 POSITIVE

Page 15 - Edit Test Limits

USE CTLE This variable allows the user to specify whether or not to apply Continuous Time Linear Equalization (CTLE). This variable is set to Yes

Page 16 - X-Replay Mode

QPHY-PCIE3 Operator’s Manual Manual Deskewing Procedures This section is only applicable to the oscilloscope and the cables connecting to the oscillo

Page 17 - QPHY-PCIE3 Testing

• Trigger i. Configure to Source to be FastEdge. ii. Set the Slope to Positive. • Parameter Measurements: i. Set the source for P1 to CX and the

Page 18 - QPHY-PCIE3 Test Descriptions

QPHY-PCIE3 Operator’s Manual 10. Save Channel X to M1. • Click File  Save Waveform. • Set Save To Memory. • Set the Source to CX. • Set the Dest

Page 19 - QPHY-PCIE3 Variables

Cable Deskewing Without Using the Fast Edge Output The following procedure demonstrates how to manually deskew two oscilloscope channels and cables

Page 20

QPHY-PCIE3 Operator’s Manual In the previous procedure, we used the default setup of the Skew parameter (which is detecting positive edges on both si

Page 22 - Error Messages

QPHY-PCIE3 Operator’s Manual Table of Contents Introduction ...

Page 23 - Manual Deskewing Procedures

Table of Figures Figure 1 - QualiPHY framework dialog and Standard selection menu. ... 5 Figure 2 -

Page 24

QPHY-PCIE3 Operator’s Manual Introduction About QualiPHY QualiPHY is a highly automated compliance test software meant to help you develop and valida

Page 25

Required Host Computer System Usually, the oscilloscope is the host computer for the QualiPHY software, and all models that meet the acquisition r

Page 26

QPHY-PCIE3 Operator’s Manual Installation and Setup QualiPHY is a Windows-based application that can be configured with one or more serial data compl

Page 27

Set Up Dual Monitor Display Teledyne LeCroy recommends running QualiPHY on an oscilloscope equipped with Dual Monitor Display capability. This allo

Page 28

QPHY-PCIE3 Operator’s Manual Using QualiPHY This section provides an overview of the QualiPHY user interface and general procedures, using examples

Commentaires sur ces manuels

Pas de commentaire