Teledyne-lecroy PCI Express 2.0 Mid-Bus Probe for Summit T24 Manuel d'utilisateur télécharger pdf

Introduction

Teledyne LeCroy's PCIe 2.0 (Gen2) mid-bus probe supports quick

and easy probing at data rates up to 5 GT/s through a simple probe

footprint designed into the PCB.

Mid-bus probes are used by system designers to probe embedded

bus signals (e.g., for serial data buses that run between chips on a

single circuit board) or simply as a convenient means to access

bus signals with a probe connector. The probe is easily attached to

an retention module mounted on top of a mid--bus footprint that is

laid out on the target test system board.

The Teledyne LeCroy PCIe 2.0 mid-bus probe uses a universal

retention module consisting of two pieces that can accommodate

both "half size" (PCIe x4 lanes) or "full size" (PCIe x8 lanes)

mid-bus footprints. Two x8 mid-bus probes can be connected to a

Summit T3-16 Analyzer and will support x16 lane widths. These

probes can be used in conjunction with the unique lane swizzling

feature on the Summit analyzers (see section 4 for details), which

allows probe signals to be reorganized logically, to give developers

additional flexibility in PCB layout.

Gen2 Mid-bus Half Size Probe Head

Gen2 Mid-bus Half Size Probe and Components (Reference

clock cable not shown)

Gen2 Mid-Bus Probe

Quick Start for Summit™

Analyzers

Before Starting

Use this document for quick installation and setup. If you

experience problems or need more information, see the

product manuals available at the Teledyne LeCroy web site or

in the Documents folder in the PETracer installation CD.

Components

The Teledyne LeCroy Gen2 mid-bus probe kits have the following

components for Summit T3-16, T3-8 and T28:

•Mid-bus Pod

• iPass Y-Cable

• Probe head with ribbon cables attached

• Reference clock cable

• Daisy chain cable (for multiple probe pods)

• 2-piece universal retention module

The Teledyne LeCroy Gen2 mid-bus probe kit has the following

components for Summit T24:

•Mid-bus Pod

• iPass x4-to-x8 straight cable

• Probe head with ribbon cables attached

• Reference clock cable

• Daisy chain cable (for multiple probe pods)

• 2-piece universal retention module

• Power Supply

1 2 3 4

Résumé du contenu

Page 1 - Analyzers

IntroductionTeledyne LeCroy's PCIe 2.0 (Gen2) mid-bus probe supports quick and easy probing at data rates up to 5 GT/s through a simple probe foo

Page 2 - Hardware Installation

3Hardware InstallationTo install the components: 1. Install the universal retention module in the Mid Bus footprint. For further details review the PC

Page 3 - Software Configuration

4Software ConfigurationThe default configuration of the Gen2 Mid-bus Probe Assembly is the (x4 width) configuration. To use Summit Analyzers, you must

Page 4 - Recording Traffic

Trademarks and ServicemarksTeledyne LeCroy and Summit are trademarks of Teledyne LeCroy. Microsoft and Windows are registered trademarks of Microsoft

Commentaires sur ces manuels

Pas de commentaire

Teledyne-lecroy PCI Express 2.0 Mid-Bus Probe for Summit T24 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Teledyne-lecroy PCI Express 2.0 Mid-Bus Probe for Summit T24. Teledyne LeCroy PCI Express 2.0 Mid-Bus Probe for Summit T24 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Teledyne-lecroy PCI Express 2.0 Mid-Bus Probe for Summit T24